How to Install a Bathtub
How to Install a Bathtub
Blog Article
They are making a few good pointers related to How to Install a Bathtub Yourself overall in this content below.
Installing a bath tub isn't specifically rocket science, but it does call for strong plumbing, carpentry, and also often, tiling skills. Replacing an old tub with a new one is additionally a reasonably tough job. If the old tub is readily obtainable, the job can move quickly; if you need to open up a wall to remove the old bathtub and also position the new bath tub, the job is much harder. In either case, the task is within a house handyman's skills, although you will require a helper to move out the old bathtub as well as set in the new one. See to it you have qualified on your own for the task and fit trying it. Rather than working with a specialist to take over a halfway-completed task, it is much better to consider utilizing one before you start. Possibilities are you might require a professional plumber to make tube links.
This short article will assist you install a brand-new bathtub in your washroom if you have currently gotten a new bathtub and don't require to change the setup of your previous supply of water pipelines.
Your tools and also material list should make up the following:
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installation, then the first thing you need to do is detach the water. After doing so, switch on the faucets to drain any type of water continuing to be in the system. The process of getting rid of the existing taps can be quite troublesome as a result of the restricted gain access to that is often the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the taps. Have a fabric all set for the remaining water that will originate from the pipes. Once the supply pipelines have actually been removed, utilize the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from transforming during this process. As soon as the taps have been eliminated, the holes in the bath/basin will have to be cleansed of any old sealing substance.
Before proceeding to fit the brand-new faucets, compare the pipeline links on the old faucets to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new faucets to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will need a plastic adapter to stop damage to the thread. One end of the port fits on the plastic tail of the faucet and the other end supplies a link to the existing supply pipelines.
If you need to fit a monobloc, then you will need minimizing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin ensuring that the washers are in location in between the faucet and also the sink. Secure the tap in place with the producer supplied backnut. When the faucet is firmly in position, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular faucet ports. The previous type should be attached to the faucet finishes initially, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Installing the Bath tub
Making use of the two wooden boards under its feet, place the bath tub in the called for setting. The wooden boards are useful in evenly spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto 4 little points.
The next objective is to make sure that the bathtub is leveled all round. This can be achieved by examining the level and adjusting the feet on the bath tub up until the spirit level checks out level.
To mount taps, fit the bottom of the outermost versatile tap connector to the ideal supply pipeline by making a compression join; after that do the exact same for the other faucet.
Turn on the supply of water and also inspect all joints and brand-new pipework for leaks and tighten them if needed. Fill the bath tub and also inspect the overflow outlet and also the typical electrical outlet for leaks.
Finally, take care of the bath paneling as defined in the producer's user's manual. Tiling as well as securing around the tub should wait up until the bathtub has actually been used a minimum of once as this will certainly resolve it into its last position.
Planning for the Installation
To start with, the supporting framework supplied with the bath needs to be fitted (if needed) according to the supplier's directions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is essential to see to it that if the tap includes a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps system to stop strain on the tub.
Fit the adaptable faucet connectors to the bottom of both faucets using 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet via the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you make use of every one of the supplied washers.
Link the trap to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath ought to now prepare to be fitted in its final setting.
Tiling Around the Tub
In the area where the bathroom satisfies the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the fitting can move enough to crack a rigid seal, triggering the water to penetrate the wall surface in between the bathroom as well as the tiling, resulting in complications with dampness and also feasible leaks to the ceiling below.
You can pick from a selection of coloured sealants to assimilate your components as well as fittings. They are offered in tubes as well as cartridges, and are capable of sealing voids approximately a size of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with spins of drenched newspaper or soft rope. Remember to always load the bath tub with water prior to sealing, to enable the movement experienced when the tub remains in usage. The sealer can break fairly very early if you do not think about this activity prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally conveniently offered on the market. It is advisable to fit the floor tiles utilizing water-resistant or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a devoted reader about Installing A Bathtub, I think sharing that piece of content was a smart idea. Sharing is good. Who knows, you could be doing someone a favor. I praise you for your time. Please stop by our blog back soon.
Book
Report this page